Indicators |
Power / TST |
This green LED is turned on when power is applied to the media converter.
Otherwise it is off. The LED will blink when in Loopback test mode. |
Fiber link on / Receive activity (LKF) |
This green LED is operational only when power is applied. The
LED is on when the 100Base-FX link is on and flashes with a 50% duty
cycle when data is received. |
Copper link on / Receive activity (LKC) |
This green LED is operational only when power is applied. The LED is
on when the 100Base-TX link is on and flashes with a 50% duty cycle when
data is received. |
Switches: On-Board (If Auto/Switch strap is set to Switch) |
Auto-Negotiation (802.3u) |
Enabled (Default) - The media converter uses 802.3u Auto-negotiation on the 100Base-TX interface. It is set to advertise full duplex.
Disabled - The media converter sets the 100Base-TX port to full duplex. |
Pause |
Pause should be enabled when all devices connected to the media
converter support pause. Auto-Negotiation must be Enabled to use this
feature.
Enabled (Default) - The Media converter will advertise Pause capability
during Auto-Negotiation on the 100Base-TX interface.
Disabled - The Media converter will advertise that it does
not have Pause capability during Auto-Negotiation on the 100Base-TX
interface. |
Link Pass Through |
Enabled (Default) - When the state of the receiver is
changed on the 100Base-TX interface it is reflected on the 100Base-FX
fiber transmitter. When the state of the receiver on the 100Base-FX
interface is changed it is reflected on the 100Base-TX transmitter.
When a Far-End Fault Indication is received on the fiber interface
the 100Base-TX transmitter is turned off. When the Far-End Fault
Indication is cleared the transmitter is turned back on.
Disabled - The 100Base-TX and the 100Base-FX fiber
interface operate independently. Far-End Fault indication on the
100Base-FX fiber interface has no effect on the 100Base-TX interface. |
Far-End Fault (FEF) |
Enabled (Default) - The media converter transmits the
Far-End Fault Indication over the 100Base-FX fiber connection whenever a
receive failure is detected on the 100Base-FX fiber connection. The
media converter continuously monitors the100Base-X fiber connection and
clears the Far-End Fault Indication condition when a valid signal is
received.
Disabled - Far-End Fault Indications are not transmitted
regardless of the condition of the receive signal on the 100Base-FX
fiber connection. |
Remote Loopback |
The media converter can perform a loopback on the 100Base-X fiber
interface.
Disabled (Default - Up)
Enabled - The 100Base-X receiver is looped to the 100Base-X
transmitter. The 100Base-TX transmitter is taken off the interface.
|
Auto-MDIX (Strap) |
If Auto-Negotiation (802.3u) is enabled, the media converter uses the
HP Auto-MDIX method for the 100Base-TX interface. If Auto-Negotiation (802.3u)
is disabled the Media converter will use the RX Energy method on the 100Base-TX
interface to set the port MDI or MDIX whichever is appropriate.
Enabled (Default) - Either a straight-through or crossover
type cable can be used to connect the media converter to the device on
the other end of the cable.
Disabled - If the partner device on the other end of the
cable does not have the Auto-MDIX feature a specific cable, either a
straight-through or crossover will be required to ensure that the media
convertor's transmitter and the partner devices transmitter are
connected to the others receiver. The Media Convertor's 100Base-TX port
is configured as MDI with this switch setting. |
Configuration Mode (Strap) |
Auto (default) enable management module to overwrite hardware switch settings
Switch - Use onboard DIP switches |
Cables |
100Base-TX |
RJ45 connector, 2 pair CAT 5, EIA/TIA 568A/B or better cable |
Magnetic Isolation |
1.5kv |
Fiber Optic Cable |
Multimode: 62.5 / 125, 50/125, 85/125, 100/140 micron
Single Mode: 9/125 micron (ITU-T 625) |
Packet Transmission Characteristics |
Bit Error Rate (BER) |
<10 -12 |
Environmental Specifications |
Operating Temperature |
0 C to 50 C (32 F to 122 F) |
Storage Temperature |
minimum range of -25 C to 70 C (-13 F to 158 F) |
Operating Humidity |
5% to 90% non-condensing |
Storage Humidity |
5% to 95% non-condensing |
Operating Altitude |
Up to 3,048 meters (10,000 feet) |
Heat Output ( BTU/HR ) |
6.8 |
Maximum Power Consumption ( Watts ) |
2.0 |
MTBF (Hours) |
595,000 |
Mechanical - Hot Swapping Card |
Edge Connecter |
32 pin DIN 41612 / IEC 60603-2 Type B/2 Male. Fist make, last break for ground and power |
Card insertion and removal |
Captive thumb screws enable fast insertion and removal. Can be further tighten with a screwdriver. |
Product Weight |
Weight |
0.15 kg, 0.33 lbs |
Packaging |
Shipping Weight |
0.33 kg, .73 lbs |
Shipping Dimensions |
203 x 38 x 152 mm, 8 x 1.5 x 6 inches |
Regulatory Approvals |
Emissions |
FCC Part 15 Class A, EN55022 Class A |
CISPR 22 Class A |
EN61000-3-2 |
Immunity |
EN55024 |
Electrical Safety |
UL 60950-1 |
EN60950 |
CE |
Laser Safety |
EN 60825-1:2007 |
Fiber optic transmitters on this device meet Class 1 Laser safety requirements
per IEC-60825 FDA/CDRH standards and comply with 21CFR1040.10 and 21CFR1040.11. |
Environmental |
RoHS - 2002/95/EC Directive |
WEEE - 2002/96/EC Directive |
Reach compliant |
Other |
ECCN: 5A991A |
HTSUS Number: 8517.62.0050 |
Perle Lifetime warranty |