Perle 05061070 - Express Systems & Peripherals

Home > Perle > Perle Industrial Media Converters > Perle MCR Series Modular Media Converters > Perle Unmanaged Fiber to Fiber Modules > 100FX MultiMode to 100FX/LX/BX/EX/ZX Single Mode Fiber Modules >

05061070

See any errors on this page?
Please let us know.

Perle C-100MM-S2ST40 - Fast Ethernet Fiber to Fiber Media Converter Module 100BASE-FX 1310nm multimode (ST) [2 km/1.2 miles] to 100Base-EX 1310nm single mode (ST) [40 km/24.9 miles]

MSRP: $905.00

ESP Price: $705.60

Contact us for Partner Pricing. (more info)

Availability: Usually Ships in 24 Hours; However, Due To Shortages Contact Sales to Verify
Product Code: 05061070

Description

Technical Specs

Drivers & Downloads

Installed in a high density Perle Media Converter Chassis, Perle's feature rich C-100MM Fast Ethernet Fiber to Fiber Media Converter Module enables transparent fiber extension of 100Base-FX multimode fiber to 100Base-FX multimode or 100Base-LX/EX/ZX/BX single mode fiber.

Perle's advanced features make the end to end fiber link completely transparent. This allows for more efficient troubleshooting and less on-site maintenance. In addition, a lifetime warranty and free worldwide technical support make Perle's C-100MM Fast Ethernet Fiber to Fiber Media Converter Modules the smart choice for IT professionals.

Whether you need to extend multimode to multimode or multimode to single mode, Perle has an extensive range of C-100MM Fast Ethernet Fiber to Fiber Media Converter Modules to meet your fiber conversion requirement.

Features

100Base-FX to 100Base-X Fiber to Fiber Media Converter Module
Multimode to multimode or multimode to single mode
Extend multimode fiber to 120km ( or more through chaining )
Choice in SC, LC and ST fiber connector models
Signal regeneration prevents signal degradation
Advanced Features: Link Pass-Through, Far-End Fault, loopback for each fiber connection
High density applications with Perle Media Converter Chassis

C-100MM Fiber to Fiber Features: 100Base-FX to 100Base-X

Link Pass-Through	When enabled, the state of the receiver on one 100Base-X interface is reflected on the other 100Base-X fiber transmitter. If disabled, the 100Base-X fiber interfaces operate independently. Far-End Fault indication on the 100Base-FX fiber interface has no effect on the other interface. Using Link Pass-Through with Far-End Fault minimizes data loss when a fault occurs. If a fault occurs, the end devices have the indication of a failure available to making trouble shooting easier.
Far-End Fault (FEF)	When enabled, the media converter transmits the Far-End Fault Indication over the fiber connection whenever a receive failure is detected. The media converter continuously monitors the fiber connection and clears the Far-End Fault Indication condition when a valid signal is received. When disabled, Far-End Fault Indications are not transmitted regardless of the condition of the receive signal on the 100Base-X fiber connection. The action the media converter takes on receiving a Far-End Fault Indication is dependent on the Link Pass Through switch setting.
Signal Regeneration	Signal regeneration maintains signal integrity and allows for maximum fiber to fiber connections without degradation.
Cascading	Media Converters can be cascaded. Two or more media converters can be chained in a link to achieve even greater distances.
Pause (IEEE 802.3xy)	Pause signaling is an IEEE feature that temporarily suspends data transmission between two devices in the event that one of the devices becomes overwhelmed. The media converter is transparent to Pause frames.
VLAN	The Media Converter is transparent to 802.1Q VLAN tagged packets.
Remote Loopback	The Media Converter can perform a loopback on each 100Base-X fiber interface.

Accessories

05059999

04030840

ESP Price: $14.40

Add

ESP Price: $25.20

Add

C-100MM Fiber to Fiber Features: 100Base-FX to 100Base-X

COMPANY

ACCOUNT

SHOPPING