Power
|
10GT to SFP
|
10GT to XFP
|
Maximum Power Consumption (watts)
|
CM-10GT: 10
CM-10GRT: 14*
|
15*
|
Indicators
|
Power / TST
|
- On: Power indication and in normal operation
- Blinking slowly: the unit is in loopback or test mode (either port)
- Red solid: the unit has a hardware error (upon power up)
- Red and blinking: the unit has a hardware error specified by combination of LK1 and LK2
|
LK1 (SFP/XFP)
|
- On: Link present
- Blinking quickly: Fiber link present and receiving data.(including test data)
- Blinking slowly: Fiber link disabled because the other fiber link went down.
- Blinking 1 sec on 3 sec off – module shut down due to high temperature.
- Off: No fiber link present or no module inserted
|
LK2
|
- On: 10GBase-T link present
- Blinking quickly: Link present and receiving data
- Blinking slowly: Link disabled because Link 1 went down
- Off: 10GBase-T link is not active
|
Switches
|
Link Mode
|
When the Link Mode is enabled (default), each port will reflect the state of its port peer using Smart Link Pass-Through. In this mode, if a link loss is detected on one port, the transmit signal on the other port is disabled “passing through” the state of the failed link. This enables managed switches and other devices to report link failures to their network NMS.
When the switch is in the down position, Smart Link Pass-Through is disabled. If a link loss is detected on one port, the transmit signal remains enabled on the other port.
|
Fiber Fault Alert
|
Enabled (Default - Up)
With Fiber Fault Alert the state of the 10 Gigabit ethernet receiver is passed to the transmitter. This provides fault notification to the partner device attached to the 10G ethernet interface of the media converter
Disabled (Down)
|
Test Mode
|
Through the use of three dip switches the unit, and its peer, can be placed into a link test mode which will verify the integrity of the link through the use of its built-in link test generator. The unit can also be placed into a simple line loopback.
|
EEE Green Ethernet
|
When enabled (default), the media converter will operate as an IEEE 802.3az Energy Efficient Ethernet (EEE) compliant device.
|
Loopback
|
Capable of performing a loopback on the 10 Gigabit interface. In this mode, all frames received on the port in loopback mode will be transmitted back. This provides users with the capability of utilizing their own in-house test generators for testing the link.
|
Connectors
|
10GT to SFP
|
10GT to XFP
|
10GBase-T (RJ45)
|
IEEE 802.3an
100 meters on CAT6A or better
|
IEEE 802.3an
100 meters on CAT6A or better
|
Pluggable 10G Fiber Transceiver slot ( Hot insertion and removable)
|
10 Gigabit SFP+ Slot
|
10 Gigabit XFP Slot
|
Voltages supplied to XFP slots
|
-
|
1.8V, 3.3V, 5V and -5.2V
|
Supported 10 Gigabit Fiber pluggable transceivers
|
IEEE 802.3ae compliant:
- 10GBase-SR
- 10GBase-LRM
- 10GBase-LR
- 10GBase-ER
- 10GBase-ZR
CWDM/DWDM
|
IEEE 802.3ae compliant:
- 10GBase-SR
- 10GBase-LRM
- 10GBase-LR
- 10GBase-ER
- 10GBase-ZR
CWDM/DWDM
|
Supported 10 Gigabit Copper pluggable transceivers
|
SFP+ Direct Attach Cable (DAC). Also known as:
- Twinax
- 10GBase-CU
- 10GSFP+Cu
- 10GBase-CX1
- 10GBase-CR1
Note: Passive and Active cable types supported
|
IEEE 802.3ak compliant:
|
Supported 2.5 Gigabit Copper pluggable transceivers
|
S-10GR Model:
SFP+ Direct Attach Cable (DAC).
Note: Passive and Active cable types supported
|
N/A
|
Supported Gigabit Fiber SFPs
|
1000Base-SX
1000Base-LX/LH
1000Base-BX
CWDM/DWDM
Note: the RJ45 interface will auto-negotiate to 1000Base-T ( Gigabit )
|
N/A
|
Chassis Slot profile
|
Two slot
|
Two slots
|
Environmental Specifications
|
10GT to SFP
|
10GT to XFP
|
Operating Temperature
|
0° C to 50° C (32° F to 122° F)
|
Storage Temperature
|
minimum range of -25° C to 70° C (-13° F to 158° F)
|
Operating Humidity
|
5% to 90% non-condensing
|
Storage Humidity
|
5% to 95% non-condensing
|
Operating Altitude
|
Up to 3,048 meters (10,000 feet)
|
Heat Output
( BTU/HR )
|
CM-10GT: 34
CM-10GRT: 48
|
51
|
MTBF (Hours)**
|
CM-10GT: 261,388
CM-10GRT: 143,838
|
286,082
|
Packaging
|
Shipping Weight
|
0.25 kg, 0.55 lbs
|
Shipping Dimensions
|
170 x 260 x 70 mm, 6.7 x 10.2 x 2.8 inches
|
Regulatory Approvals
|
Emissions
|
FCC Part 15 Class A, EN55022 Class A
|
CISPR 22 Class A
CISPR 32:2015/EN 55032:2015 (Class A)
CISPR 24:2010/EN 55024:2010
|
EN61000-3-2
|
Immunity
|
EN55024
|
Electrical Safety
|
UL 60950-1
|
IEC 60950-1(ed 2); am1, am2
EN 60950-1:2006+A11:2009+A1:2010+A12:2011+A2:2013
|
CE
|
Laser Safety
|
Dependent on SFPs used. SFPs that meet Class 1 Laser safety requirements per IEC-60825 FDA/CDRH standards and comply with 21CFR1040.10 and 21CFR1040.11 are recommended for use with this product.
|
Environmental
|
Reach, RoHS and WEEE Compliant
|
Other
|
ECCN: 5A991
|
HTSUS Number: 8517.62.0050
|
Perle Limited Lifetime Warranty
|