| Power |
|---|
| DC Power Requirements |
PoE models: 46 - 57 vDC
PoE+ models: 52 - 57 vDC |
| Power Consumption |
3.5 Watts |
| Power Over Ethernet (PSE) |
PoE models: maximum to 15.4 watts
PoE+ models: up to 30 watts |
| PoE Options |
Alternative A ( power on pins 1,2 and 3,6 )
Alternative B ( power on pins 4,5 and 7,8 )
Legacy PoE ( IE wireless access points ) - ( reverse polarity on pins 4,5 and 7,8 )
Legacy large capacitor detect ( pins 4,5 and 7,8 ) |
| Power Connector |
2-Pin pluggable terminal block |
| Indicators |
| Power ( PWR ) |
This green LED is turned on when power is applied to the media
converter. Otherwise it is off. The LED will blink slowly when either
fiber port is in Loopback test mode. The LED will blink quickly if there
is a hardware failure where the reason code can be identified through a
combination of FDF,LKF, FDC and PSE indicator LEDs |
Fiber link on / Receive activity
( LKF 1/2 ) |
This green LED is operational only when power is applied. The LED will blink along with transmit/receive data on the fiber port
If a loss of link on the copper port results in a Link
Passthrough condition to the fiber port, this LED will blink at a rate
of once every 2 seconds until the condition is cleared. |
Copper link on / Receive activity
( LKC 1/2 ) |
This green LED is operational only when power is applied.
The LED will blink along with transmit/receive data on the 10/100/1000
UTP port
If a loss of link on the copper port results in a Link
Passthrough condition to the fiber port, this LED will blink at a rate
of once every 2 seconds until the condition is cleared. |
| Fiber Duplex ( FDF 1/2 ) |
This green LED is operational only when power is applied. The
LED is on when the 10/100/1000Base-X link is operational in full duplex
mode. The LED is off when in half duplex. If the Auto-Neg switch is
turned off, this LED will always be on |
| Copper Duplex ( FDC 1/2 ) |
This green LED is operational only when power is applied. The
LED is on when the 10/100/1000Base-T link is operational in full duplex
mode. The LED is off when in half duplex |
| 100/1000 |
This multi-color LED is operational only when power is
applied. The LED is green when the speed of the copper ethernet port is
running at 1000 Mbps. The LED is yellow when the speed of the copper
Ethernet port is running at 100 Mbps. The LED is off when in 10 Mbps. |
| PSE Status ( PSE 1/2 ) |
This LED will signify the status of the PSE function. Using
multi-color and blinking the unit will show the following status for
the PSE;
GREEN — Solid: The PSE has successfully detected a compliant
PD and is applying power over the UTP (for legacy pin out simply show
active power when applied)
YELLOW — Solid: The PSE is not active. This means the PSE has been configured to provide power, but the PD is :
- Not connected
- Has not detected a compliant PD and is not applying power
- PSE has turned off power for Reset function
OFF — PSE function switch disabled
RED — Blinking: Error Conditions
- Capacitance too High — 1 blink
- Resistance too Low or short circuit — 2 blinks
- Resistance too high or open circuit — 3 blinks
|
| Switches - accessible through a side opening in the chassis |
| Auto-Negotiation (802.3u) |
Enabled (Default) - The media converter uses 802.3u
Auto-negotiation on the 10/100/1000Base-T interface. It is set to
advertise full duplex, half duplex, pause and remote fault
capabilities.
Disabled - The media converter sets the port according to the position of the speed and duplex switches. |
| Link Mode |
Link Mode provides a transparency to the state of the copper
link allowing for simplified trouble shooting from the devices connected
to the media converter.
Normal (Default — Up)
With Fiber Auto Negotiation enabled when the copper link goes
down the 1000Base-X link is brought down. The 1000Base-X link will
advertise Remote Fault (Link Fault).
With Fiber Auto Negotiation disabled the state of the copper link has no effect on the 1000Base-X link.
Smart Link Pass Through (Down)
With Fiber Auto Negotiation enabled the behavior is as follows.
When the copper link goes down the 1000Base-X link is brought down. The
1000Base-X link will advertise Remote Fault (Link Fault). When Remote
Fault (Link Fault) is received on the 1000Base-X interface the copper
transmitter will be turned off. When the copper receiver is off the
1000Base-X transmitter will be turned off. When the 1000Base-X receiver
goes off the copper transmitter will be turned off.
With Fiber Auto-Negotiation disabled the behavior is as follows.
When the copper receiver is off the 1000Base-X transmitter will be
turned off. When the 1000Base-X receiver goes off the copper transmitter
will be turned off. |
| Fiber Fault Alert |
The Fiber Fault Alert switch has meaning when Auto-Negotiation is
disabled
Enabled (Default - Up)
When the 1000Base-X receiver is off the 1000Base-X transmitter
is turned off. Periodically the 1000Base-X receiver will be turned on
for a short period to allow the condition to clear if the 1000Base-X
link partner is using a similar feature.
Disabled (Down)
|
| Loopback |
The media converter can perform a loopback on the 1000Base-X fiber interface.
Disabled (Default - Up)
Enabled - The 1000Base-X receiver is looped to the 1000Base-X transmitter. The copper transmitter is taken off the interface.
|
| Speed Copper |
100 (Default)
10 |
| Duplex Copper |
Full (Default)
Half |
| Fiber Negotiation |
Up: The Media Converter will negotiate Ethernet parameters on
the fiber connection. This will ensure that the most optimal
connection parameters will be in effect. If connecting to another
Perle Media Converter, this parameter should be set to Auto. The
Media Converter Module will advertise 1000Mbps, Full and Half
Duplex, no Pause.
Down: The Media Converter Module’s fiber will be fixed to
1000Mbps, Full Duplex. |
| Auto-MDIX (Internal Strap) |
If Auto-Negotiation (802.3u) is enabled, the media
converter determines the current cable pinout to use on the copper
interface. If Auto-Negotiation (802.3u) is disabled the Media converter
will use the RX Energy method on the copper interface to set the port
MDI or MDIX whichever is appropriate.
Enabled (Default) - Either a straight-through or crossover
type cable can be used to connect the media converter to the device on
the other end of the cable.
Disabled - If the partner device on the other end of the
cable does not have the Auto-MDIX feature a specific cable, either a
straight-through or crossover will be required to ensure that the media
converter's transmitter and the partner devices transmitter are
connected to the others receiver. The Media converter's 100Base-TX port
is configured as MDI-X with this switch setting. |
| PSE Power |
Settable for each UTP port available.
When enabled (UP), the media converter will perform a Power
Sourcing Equipment (PSE) function as per IEEE802.3af or 802.3at
standards (relevant model).
Default is "enabled" |
| PD Power Reset |
This is a technique to perform a power reset on a PD device(s) attached.
When enabled ( down ), the media converter will upon loss of
link on any fiber port, turn off PSE output power to the PD device(s)
for 2 seconds then turn the power back on. The power remains on until
any fiber link transitions from up to down again.
With Passthrough enabled ( Link Mode enabled and Fiber
Auto-Negotiation enabled ) , a loss of link on the fiber resulting from a
loss of link on the copper, a PD Power Reset till still occur.
When PD Power Reset disabled, loss of fiber link has no effect on PSE power to the PD device(s). |
PoE Power Options
( Internal Straps ) |
Set to Alternative A ( default ):
Set to Alternative B:
Set to Legacy Pre-Standard: |
Pins 3,6 Neg, Pins 1,2 Pos
Pins 7,8 Neg, Pins 4,5 Pos
Pins 7,8 Pos, Pins 4,5 Neg |
|
| Connectors |
| 10/100/1000Base-T |
RJ45 connector
2 pair CAT5, EIA/TIA 568A/B or better cable for 10/100.
4 pair CAT5 UTP cable for Gigabit. |
| Magnetic Isolation |
1.5kv |
| Fixed Fiber |
Dual multimode or single mode ( Duplex ) fiber - SC, ST
Single strand fiber ( Simplex ) - SC
LC - obtained by inserting an SFP ( LC ) in an SFP slot model
|
Small Form Factor Pluggable
( SFP ) slot |
SFP slot models: Empty slot for 1000Base-X or 100Base-X SFP modules supplied by Perle, Cisco or other manufacturers of MSA compliant SFPs.
Hot insertion and removable ( hot swappable ). |
| Filtering |
| Filtering |
1024 MAC Addresses |
| Frame Specifications |
| Buffer |
1000 Kbits frame buffer memory |
| Size |
Maximum frame size of 10,240 bytes -- Gigabit
Maximum frame size of 2048 bytes -- Fast Ethernet |
| Environmental Specifications |
| Operating Temperature |
-40 C to 75 C (-40 F to 167 F) |
| Storage Temperature |
-40 C to 85 C (-40 F to 185 F) |
| Operating Humidity |
5% to 90% non-condensing |
| Storage Humidity |
5% to 95% non-condensing |
| Operating Altitude |
Up to 3,048 meters (10,000 feet) |
| Heat Output ( BTU/HR ) |
20.5 |
| MTBF (Hours) |
| Model Type |
MTBF |
1 UTP, fixed fiber
1 UTP, 1 SFP
|
370,535
432,168
|
|
| Mounting |
| Din Rail Kit |
Optional |
| Rack Mount Kit |
Optional |
| Product Weight and Dimensions |
| Weight |
0.45 Kg, 1.0 lbs (no power adaptor) |
| Dimensions |
150 x 95 x 26 mm, 5.9 x 3.7 x 1.0 inches |
| Packaging |
| Shipping Weight |
0.52 kg, 1.1 lbs |
| Shipping Dimensions |
150 x 210 x 40 mm, 5.9 x 11 x 2.8 inches |
| Regulatory Approvals |
| Emissions |
FCC Part 15 Class A, EN55022 Class A |
| CISPR 22 Class A |
| EN61000-3-2 |
| Immunity |
EN55024 |
| Electrical Safety |
UL 60950-1 |
| EN60950 |
| CE |
| Environmental |
RoHS - 2002/95/EC Directive |
| WEEE - 2002/96/EC Directive |
| Reach compliant |
| Other |
ECCN: 5A991A |
| HTSUS Number: 8517.62.0050 |
| Perle Lifetime warranty |
