 |
 |
 |
|
Introduction
The ioLogik E1200 Series supports the most often-used protocols for retrieving I/O data, making it capable of handling a wide variety of applications. Most IT engineers use SNMP or RESTful API protocols, but OT engineers are more familiar with OT-based protocols, such as Modbus and EtherNet/IP. Moxa's Smart I/O makes it possible for both IT and OT engineers to conveniently retrieve data from the same I/O device. The ioLogik E1200 Series speaks six different protocols, including Modbus TCP, EtherNet/IP, and Moxa AOPC for OT engineers, as well as SNMP, RESTful API, and Moxa MXIO library for IT engineers. The ioLogik E1200 retrieves I/O data and converts the data to any of these protocols at the same time, allowing you to get your applications connected easily and effortlessly.
Daisy-Chained Ethernet I/O Connection
This industrial Ethernet remote I/O comes with two switched Ethernet ports to allow for the free flow of information downstream to another local Ethernet device, or upstream to a control server via expandable daisy-chained Ethernet I/O arrays. Applications such as factory automation, security and surveillance systems, and tunneled connections can make use of daisy-chained Ethernet for building multidrop I/O networks over standard Ethernet cables. Many industrial automation users are familiar with multidrop as the configuration most typically used in fieldbus solutions. The daisy-chain capabilities supported by ioLogik Ethernet remote I/O units not only increase the expandability and installation possibilities for your remote I/O applications, but also lower overall costs by reducing the need for separate Ethernet switches. Daisy-chaining devices in this way will also reduce overall labor and cabling expenses.
Save Time and Wiring Costs with Peer-to-Peer Communications
In remote automation applications, the control room and sensors are often far removed, making wiring over long distances a constant challenge. With peer-to-peer networking, users may now map a pair of ioLogik Series modules so that input values will be directly transferred to output channels, greatly simplifying the wiring process and reducing wiring costs.
User-Definable Modbus TCP Addressing for Painless Upgrading of Existing Systems
For Modbus devices that are controlled and detected by fixed addresses, users need to spend a vast amount of time researching and verifying initial configurations. Users need to locate each device’s networking details, such as I/O channels or vendor-defined addresses, to enable the initial or start address of a SCADA system or PLC. Devices that support user-definable Modbus TCP addressing offer greater flexibility and easier setup. Instead of worrying about individual devices, users simply configure the function and address map to fit their needs.
Push Technology for Events
When used with MX-AOPC UA Server, devices can use active push communications when communicating changes in state and/or events to a SCADA system. Unlike a polling system, when using a push architecture for communications with a SCADA system, messages will only be delivered when changes in state or configured events occur, resulting in higher accuracy and lower amounts of data that need to be transferred.
| Inputs and Outputs |
| Thermocouple Inputs |
8 channels |
| • Thermocouple Input |
| Sensor Type |
J, K, T, E, R, S, B, N |
| Millivolt Type |
• Mode: ±78.126 mV, ±39.062 mV, ±19.532 mV
• Fault and over-voltage protection: -35 to +35 VDC (power off); -25 to +30 VDC (power on)
|
| Sampling Rate |
12 samples/sec (all channels) |
| Resolution |
16 bits |
| Accuracy |
±0.1% FSR @ 25°C
±0.3% FSR @ -40 and 75°C
|
| Input Impedance |
10M ohms |
| • LAN |
| Ethernet |
2 x 10/100 Mbps switch ports, RJ45 |
| Protection |
1.5 KV magnetic isolation |
| Protocols |
Modbus/TCP, TCP/IP, UDP, DHCP, Bootp, HTTP |
| • Power Requirements |
| Power Input |
24 VDC nominal, 12 to 36 VDC |
| Power Consumption |
118 mA @ 24 VDC |
| • Physical Characteristics |
| Wiring |
I/O cable max. 14 AWG |
| Dimensions |
27.8 x 124 x 84 mm (1.09 x 4.88 x 3.31 in) |
| Weight |
under 200 g |
| • Environmental Limits |
| Operating Temperature |
Standard Models: -10 to 60°C (14 to 140°F)
Wide Temp. Models: -40 to 75°C (-40 to 167°F)
|
| Storage Temperature |
-40 to 85°C (-40 to 185°F) |
| Ambient Relative Humidity |
5 to 95% (non-condensing) |
| • Standards and Certifications |
| Safety |
UL 508 |
| EMI |
FCC Part 15 Subpart B Class A |
| EMS |
IEC 61000-4, IEC 61000-6 |
| Shock |
IEC 60068-2-27 |
| Freefall |
IEC 60068-2-32 |
| Vibration |
IEC 60068-2-6 |
| • MTBF (mean time between failures) |
| Time |
631,418 hrs |
| Database |
Telcordia (Bellcore) |
| • Warranty |
| Warranty Period |
5 years |
|
|
|
 |
|
 |
|
|
|
 |
|
 |
|
Features
- Built-in 2-port Ethernet switch for
daisy-chain topologies
- Free support of Moxa’s push-based
Active OPC Server Lite
- Seamlessly connect to any SCADA system
-
Save 80% on network bandwidth
- I/O response that’s seven times
faster
- User-defined Modbus/TCP addressing
- MXIO programming library for
Windows and WinCE VB/VC.NET and Linux C APIs
- Web configuration with
Import/Export function
|
|
|
|
|
|
|